The tyre speed rating is the letter after the load index (for example the V in 91V) and shows the maximum sustained speed the tyre is certified for: H is 210 km/h, V is 240 km/h, W is 270 km/h, Y is 300 km/h. The load index is the number (91 means 615 kg per tyre). Always fit tyres with a load index and speed rating equal to or higher than your car's original specification.

Where to find the speed rating and load index
Look at the sidewall and find the tyre size, something like 225/45 R17 94W. The last part, '94W', is the service description. The number is the load index and the letter is the tyre speed rating. You'll find the original specification for your car on the placard inside the driver's door or fuel flap and in the owner's manual.
When customers send me a sidewall photo on WhatsApp to get a quote, these two characters are the bit I check most carefully, because they rule out a lot of cheap alternatives that look the same size on paper.
Tyre speed rating chart
The speed rating is the maximum speed the tyre can sustain at its rated load under test conditions. It is not a suggestion to drive at that speed, and it applies to a correctly inflated, undamaged tyre.
| Letter | Max speed (km/h) | Typical use |
|---|---|---|
| Q | 160 | Some mud-terrain and light-truck tyres |
| R | 170 | Heavy-duty light truck, some all-terrain |
| S | 180 | Some all-terrain and van tyres |
| T | 190 | Economy cars, many pickups and all-terrain |
| H | 210 | Most family sedans and SUVs |
| V | 240 | Sporty sedans, premium SUVs |
| W | 270 | Performance and luxury cars |
| Y | 300 | High-performance cars |
| (Y) | Above 300 | Supercars; shown in brackets around the service description |
Load index chart (common UAE sizes)
The load index is a code for the maximum weight each tyre can carry at the correct pressure. Multiply by four for a rough idea of the total, but remember the car's weight isn't spread evenly and the margin is there for a reason.
| Load index | Max load per tyre (kg) | Load index | Max load per tyre (kg) |
|---|---|---|---|
| 88 | 560 | 102 | 850 |
| 91 | 615 | 104 | 900 |
| 94 | 670 | 107 | 975 |
| 95 | 690 | 110 | 1,060 |
| 97 | 730 | 112 | 1,120 |
| 98 | 750 | 116 | 1,250 |
| 100 | 800 | 121 | 1,450 |
XL, reinforced and HL tyres
XL (extra load) or 'Reinforced' tyres have a stronger construction that allows a higher load index in the same size when run at a higher pressure. For example, a standard 225/45 R17 is typically 91, while the XL version is 94. Many European cars and most heavier SUVs specify XL from the factory.
HL (high load) is a newer marking you'll see on some EV and large SUV tyres, printed before the size, for example HL 255/45 R19 104. It goes beyond XL in the same size to cope with heavy battery packs. If your car came on HL tyres, an ordinary XL replacement may not have enough load capacity, so check the index rather than assuming.
- Standard load (SL): no extra marking.
- Extra load (XL / Reinforced / RF): higher load index, needs higher pressure to carry it.
- High load (HL): higher still, mainly EVs and heavy SUVs.
- Light truck (LT) and C-rated van tyres: a different system with load ranges, common on pickups and vans.
Can you fit a lower speed rating or load index?
Load index: no. Never fit a tyre with a lower load index than the car's specification. It is an engineering limit, and running under it overloads the casing, which builds heat and can lead to failure. It can also cause problems with insurance after an accident.
Speed rating: the safe practice is the same. Fit the same rating or higher. Going one step lower might seem harmless if you never drive above 140 km/h, but the rating also reflects how well the tyre's construction handles heat, and in a UAE summer that heat margin matters. Going higher is fine and is often what we do when the exact rating isn't in stock.
| Change | Acceptable? | Notes |
|---|---|---|
| Same load index and speed rating | Yes | The ideal |
| Higher speed rating, same load | Yes | Steering may feel slightly firmer |
| Higher load index (e.g. XL instead of SL) | Yes | Set pressure according to the load required |
| Lower speed rating | Not recommended | Reduces heat and speed margin |
| Lower load index | No | Unsafe, especially on heavy SUVs and EVs |
Why these numbers matter more in the UAE
Two things make the UAE tough on tyres: very high ambient and road temperatures, and long sustained runs at highway speed, Dubai to Abu Dhabi, out to Al Ain, or across to Ras Al Khaimah. A tyre doing 120 km/h for an hour on 65°C asphalt is working much harder than the same tyre on a cool European motorway.
Add a full family, luggage on a Land Cruiser roof rack, or a boat trailer behind a Patrol, and you're closer to the load limit than you might think. This is exactly where a correctly rated tyre at the correct pressure earns its money. I've seen more failures on overloaded SUVs with underrated replacement tyres than on any sports car.
Mixing speed ratings on one car
Sometimes only two tyres need replacing and the matching rating isn't available. If you mix ratings, the car's effective limit becomes that of the lowest-rated tyre, and the general practice is to put the higher-rated pair on the rear axle for stability. That's what we follow.
Better still is to keep the same rating across the axle, and ideally across all four. Tyres with different speed ratings usually have different constructions, and that can change how the car responds in a sudden lane change at speed. On sports cars and anything with a staggered setup, I'd always keep each axle matched in brand, pattern and rating.
Temporary space-saver spares are a separate case. They often carry a lower rating and have a maximum speed printed on them, commonly 80 km/h. Respect that limit until the proper tyre is back on.
A quick worked example
Say your Toyota Camry placard says 235/45 R18 94V. You could fit 94V, 94W, 98W XL or 98Y XL tyres. You should not fit 91V or 94H. If a shop offers you 94H because it's cheaper, ask why; it's a step down from what Toyota specified.
When we quote, we match or exceed your original service description and tell you clearly if a suggested tyre differs. If you're unsure, send us a sidewall photo and the door-placard photo and we'll check before anything is fitted.
Frequently asked questions
What does the speed rating on a tyre mean?
It is the letter after the load index and shows the maximum sustained speed the tyre is certified for at its rated load. For example, H means 210 km/h, V means 240 km/h and W means 270 km/h.
What does load index 91 mean?
A load index of 91 means each tyre can carry up to 615 kg at its correct inflation pressure. Higher numbers mean more capacity: 94 is 670 kg and 100 is 800 kg.
Can I use tyres with a higher speed rating than my car needs?
Yes. A higher speed rating is perfectly fine and sometimes gives slightly sharper steering. Just keep the load index at least equal to the original specification.
Is it illegal to fit a lower load index tyre?
Fitting a lower load index than the vehicle specification is unsafe and can create problems with insurance or inspection. It should never be done, especially on heavy SUVs, pickups and EVs.
What is the difference between XL and HL tyres?
Both are reinforced to carry more load than a standard tyre of the same size. XL (extra load) is the long-established version, while HL (high load) is a newer, higher category used mainly on heavy EVs and large SUVs.
Where do I find the correct load and speed rating for my car?
Check the tyre placard on the driver's door pillar or fuel flap, or the owner's manual. The original tyres on the car will also show it after the size, for example 94V.
Faisal Imram has spent eight years fitting, repairing and diagnosing tyres across the UAE — from villa driveways in Arabian Ranches to hard shoulders on Sheikh Mohammed Bin Zayed Road. He leads the mobile tyre team at 800Sayara and writes our guides from what he sees on the job every day. More from Faisal.